Our rugged industrial flat panel LCD monitor for rack mount, swivel-arm mount, VESA mount, panel mount is constructed of heavy duty metal for ruggedness. Ruggedized for industrial environment, the flat panel LCD come in a wide range of sizes from cost-effective 15 inch XGA models to high resolution 19 inch and 20 inch UXGA LCD monitors. All include built-in A/D (analog/digital) conversion board for interfacing to standard analog video cards. High resolution models also include DVI interface. Front panel OSD control buttons let you adjust the display for optimum viewing.

Portable Computer

Touch Panel PC

Rack Console

Rack Mount LCD

Support

What's New

Product Technical Support

Flat Panel LCD Monitors


My LCD displays this message "OUT OF RANGE" when I connect it to my computer. What should I do?

Either the resolution, or the vertical fresh rate, or both of these settings of your graphics card has exceeded the range of the LCD.

  • First, determine the resolution of your LCD. If your graphics card is set to a higher resolution than that of the LCD, you must reset it to the LCD's resolution (or a resolution below the native resolution of the LCD). Image quality is best when the graphics card resolution matches the native resolution of the LCD. If your graphics card's resolution is set below that of the LCD, most LCD monitors have auto-scaling feature that stretches the image to fill the entire screen.
  • Next, check the "refresh rate" of the graphics card (also known as vertical sync, screen refresh). All of our flat panel LCD monitors will work at 60Hz.

top of page

How high can I set my graphics card's refresh rate? Will low refresh rate impact the stability of the images?
Our LCD monitors have maximum refresh rates of either 70 HZ or 75 HZ. Because the maximum refresh rate differs from model to model, you should check the model's technical specification. Unlike CRTs, LCD technology is inherently flickerless and the refresh rate should not affect the stability or quality of the displayed images. The reresh rate is actually an architectural hold-over from CRT designs. For our LCD monitors, the optimum setting for your video card is the LCD monitor's native resolution at 60Hz refresh rate.

top of page

The image on my LCD seems to jitter. How can I fix it?

In an LCD, each pixel corresponds to a specific set of red, green, and blue LCD cells. When an LCD monitor gets an analog signal, it has to decide which cell is supposed to display a specific pixel. If it can't make up its mind, the pixel will jump back and forth between adjacent sets of cells, creating an annoying jitter in the display. LCDs have built-in controls to minimize or eliminate the problem:

  • Look for an "automatic" adjustment feature that will eliminate the jitter, and adjust image size and position at the same time. The feature may be available as a button on the control panel (often labeled Auto) or as a choice in the on-screen display (OSD).
  • If the monitor does not have an automatic adjustment feature, or the feature doesn't stop the jitter completely, you'll have to adjust the settings manually. Start by adjusting the coarse timing for the LCD, which should be an available setting in the onscreen display (OSD). Typical names for this feature are Clock and Tuning. Increase or decrease the setting until you have minimized the jitter you see in the image. Next, you may also adjust the fine timing for the LCD. Typical names for this adjustment are Phase and Fine Tuning.

top of page

I see small bright/dark dots on my LCD every time I turn it on. Is it defective?

Imperfections may appear on the screen if either the pixel or sub-pixel is stuck always ON; a bright spot on a dark background, or it is stuck always OFF; a dark spot on a bright background. The criteria for replacement of LCDs with defective pixels depends on the manufacturer of the LCD. Use the following as a guideline to see if your LCD is defined as "defective" and possibly replaceable through your manufacturer.

The LCD meets one of the following criteria:

  • a total of 15 stuck sub-pixels or 10 stuck full pixels
  • 10 stuck red sub-pixels
  • 10 stuck blue sub-pixels
  • 4 stuck green sub-pixels
  • No more than two "adjacent" pixels may be stuck, adjacent being defined as less than 2.5mm edge to edge
  • No more than two pairs of two-adjacent stuck pixels per display

note: A pixel (picture element) consists of one red, one green and one blue sub-pixel. A stuck green sub-pixel is more visible than blue or red.

Related topics:

top of page

Screen image on my wide screen LCD seems to be distorted. It looks compressed vertically.

Your wide screen LCD is using automatic scaling to stretch video images at 4:3 aspect ratio (640x480, 800x600 and 1024x768) to fill the entire 16:10 aspect ratio (1280x768) screen.

  • Turn on the LCD monitor's on-screen-menu and see if there is a choice to set it to 4:3 aspect ratio. The image will be restored but there will be two black side bars on each side of the image.
  • If your LCD monitor's on-screen-menu does not include options to select 4:3 aspect ratio, you'll need to use a video card that supports the wide aspect ratio resolution of your LCD.

top of page